AES E-loop Commerical Presence

Description

AES E-loop Commerical with LCD Transceiver Presence

Presence MODE

The Commercial Wireless Vehicle Detection System uses magnetometer sensors to detect the presence of oncoming vehicles.

These detections are transmitted to a nearby transceiver for gate activation. After the vehicle is detected, the e-loop will switch to radar mode. The sensors are installed on the surface of entry or exit passages using dynabolts, contain four replaceable Lithium batteries, and can withstand almost any vehicle.

The Radar sensors can detect vehicles that are stopped above the e-loop. The added radar utilises two-way radio communication protocol for reliable operation. Once the magnetometer sensor detects an oncoming vehicle, the transceiver relay will be latched and confirmation will be sent back to the e-loop. If the magnetic field drops below the set threshold, the radar will check if a vehicle is present. If no vehicle is detected, an unlatch command is sent to the relay, and the transceiver will send a confirmation to the e-loop. If the confirmation is missed, multiple attempts will be made to ensure A safe operation. Radar settings can be adjusted using the e-diagnostics remote. Settings that can be changed include; Dead zone, sensor distance, sensitivity, magnetic field release level, confirmation mode.

AES E-loop Commerical with LCD Transceiver Presence includes

• 1 x e-Loop Presence mode wireless detection module..
• 1 x LCD transceiver (Trans-200).
• 2 x Dyna bolts.
• 1x Magnet.

Introducing a new concept in wireless vehicle detection. The inground e-Loop replaces traditional wired inductive loops, saving time and money while increasing reliability.

Installation in 3 simple steps
1. Code in the e-Loop
2. Secure the e-Loop to the driveway
3. Calibrate the e-Loop… and you’re ready to operate in less than 15 minutes.
Save many hours of installation time compared to wired loop systems.

Features

• Dual sensor technology.
• Magnetic field and Radar detection.
• Quick and easy installation.
• Compact profile –only 28mm high x 220mm diameter.
• Not affected by ground movement.
• 10600 mA battery giving up to 10 years battery life.
• High security 128 bitencryption.
• Range 50 metres.
• Made of high-impact plastic (10 tonne static load limit).

E-TRANS 50 Single Channel Transceiver

Introducing a bidirectional wireless access control system for gate and door applications.

Featuring a compact design with exceptional range, the e-Trans-50 is designed to manage access control for home and commercial systems.

Features

• Compact design with exceptional range.
• SMA connector for standard for optional long-range antenna connection.
• Wide Voltage Range: 10-36V DC.
• Exceptionally low Current draw: standby 4.5 m/a, active 30 m/a.
• Frequency: 433.39 MHz.
• Remote storage: 50 remotes, 4 x e-Loops, 4 x Keypads, 4 x Entry Buttons.
• Relay: 1-amp contact rating, COM and N/O connections x 1 relay.
• Multiple Modes: Pulse, Latch and Hold.

PLEASE NOTE THERE IS NO NORMALLY CLOSED CONTACT ON THE E-TRANS 50. HOLD OPEN ONLY

E-TRANS 100  Two Channel Transceiver

Features

• 2 channel transceiver.
•  Long range with SMA connector for external antenna options.
• Stores 2 x e-Loops and 50 x remotes in each channel.
• 10-28VAC or 10-36VDC power input.
• Low current draw 12mA in standby, can be set to LDC mode.
• 4.5mA for solar applications.
• 433.39 MHz frequency.
• 250 Hz bandwidth.
• 128bit AES encryption for total security.
• 2 x 1A relay contacts.
• NC/NO/COM outputs.
• Can be set to pulse latch or hold mode.
• Suspension inputs for each relay.

E-TRANS 200 LCD Transceiver

Introducing a bidirectional wireless access control system for gate and door applications.
With a unique lock-out function, this high-end accessory is designed to manage access control for commercial multi-unit complexes with up to 200 units, with functions also suitable for home systems.

Features

• Simple to use menu functions with LCD display.
• High sensitivity 433 MHz -126 dBm receiver with 20 dBm Transmission output.
• External SMA connector to allow for the connection of different antennas.
• Wide input voltage range from 10V to 36V ACDC.
• 2 relay outputs with the ability to set to Pulse, Hold or Latch mode.
• Selectable ultra-low standby power consumption of only 4.5 m/a making it ideal for solar applications.
• 200 code storage with remote ID selection making it ideal for unit applications.
• Ability to delete individual remote devices.
• Unique lock-out feature allowing you to lock out entry buttons, e-Loops and keypads using the lock and unlock function on the e-Remote.
• Ability to connect to the e-Loop to access menus and change settings.
• Test mode which allows you to test relay outputs, radio signal strength and radio interference.

For our full range of Induction Loops Click Here

For more information from the manufacturer please click here

FREE UK Mainland delivery on all orders over £100! Contact us about shipping to Ireland or Northern Ireland.